View AT7913EKB-E_8909901.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1 7833b?aero?05/09 features ? leon2-ft sparc v8 processor ? 5 stage pipeline ? 4k instruction caches / 4k data caches ? meiko fpu ? interrupt controller ? uart serial links ? 32-bit timers ? memory interface ? general purpose io ? debug support unit (dsu) ? fifo interface ? adc/dac interface ? 24 channels ? 8bit/16bit wide data bus ? two can interface ? two bidirectional spacewire links ? full duplex communication ? transmit rate from 1.25 up to 200 mbit/s in each direction ? spacewire link performance ? at 3.3v : 200mbit/s full duplex communication ? jtag interface ? operating range ? voltages ? 1.65v to 1.95v - core ? 3v to 3.6v - i/o ?temperature ? - 55c to +125c ? maximum power consumption ? at 3.6v with a yyymhz clock: 150mw ? radiation performance ? tested up to a total dose of 300 krad (si) according to the mil-std883 method 1019 ? no single event latchup below a let of 80 mev/mg/cm2 ? esd better than 2000v ? quality grades ? qml-q or v with smd ? package: 349pins mcga ? mass: 9 grams spacewire - remote terminal controller (rtc) at7913e advanced information
2 at7913e advanced information 7833b?aero?05/09 1. description the spacewire remote terminal controller (rtc) device is a bridge between the spacewire network and the can bus, provid ing a fully integrated system. additional features are provided to carter for autonomy of remote terminals and to relieve the cen- tral processing chain of repetitive standard acquisitions and management duties. the spacewire-rtc device can be used both in non-intelligent nodes and in nodes with local intelligence. the spacewire-rtc device includes an em bedded microprocessor, a can bus control- ler, adc/dac interfaces for analogue acquisi tion/conversion, standard interfaces and resources (uarts, timers, general purpose input output). the spacewire-rtc device can be operated stand-alone or with a number of external devices such as sram, prom and fifo memories, adc and dac converters. the device can be managed locally by the on-chip processor, or remotely via its spacewire link interfaces. spacewire-rtc device can operate as a single-chip system, with soft- ware being uploaded to its on-chip memory via the spacewire link interface, forming a compact solution for remotely controlled applicat ions. or it can operate in a full-size sys- tem, with software being decompressed from local prom and executed from multiple fast and wide sram memory banks. the device provides scalability in terms of use of external devices and operating frequency. figure 1-1. at7913e spacewre rtc block diagram
3 at7913e advanced information 7833b?aero?05/09 2. pin configuration table 1. pin assignment signal pin signal pin signal pin signal pin signal pin signal pin adaddr_0 k5 fifop_0 f6 leonpio_15 m9 memd_14 k17 spwsout_p_0 a12 vdb22 j15 adaddr_1 l5 fifop_1 f4 leonwdn n7 memd_15 k15 spwsout_p_1 m19 vdb23 j16 adaddr_2 k2 fifordn f2 lvdsref0 d11 memd_16 k13 sysclk r1 vdb24 g15 adaddr_3 k7 fifowrn e4 lvdsref1 l16 memd_17 j19 sysresetn r4 vdb25 f17 adaddr_4 l1 gpio_0 a9 mema_0 p9 memd_18 h17 taptck e10 vdb26 f18 adaddr_5 m3 gpio_1 b9 mema_1 r8 memd_19 j18 taptdi g10 vdb30 d17 adaddr_6 l2 gpio_2 c9 mema_2 n9 memd_20 j17 taptdo b10 vsa0 v18 adaddr_7 l3 gpio_3 d9 mema_3 v9 memd_21 k11 taptms c10 vsa1 v4 adcs p2 gpio_4 f9 mema_4 u9 memd_22 h15 taptrstn e9 vsa2 w4 addata_0 k9 gpio_5 j10 mema_5 p10 memd_23 h19 vsb31 h8 vsa3 b18 addata_1 m5 gpio_6 e8 mema_6 m10 memd_24 j12 vsb32 h3 vsa4 a4 addata_2 m1 gpio_7 b8 mema_7 w10 memd_25 h18 timeclk j5 vsa5 a16 addata_3 l8 gpio_8 e7 mema_8 r9 memd_26 g17 timetrig_1 k4 vsa6 b2 addata_4 m4 gpio_9 d8 mema_9 t10 memd_27 j13 timetrig_2 k3 vsa7 b16 addata_5 n3 gpio_10 c7 mema_10 r11 memd_28 h14 vda0 v17 vsa8 c3 addata_6 l7 gpio_11 g9 mema_11 v10 memd_29 f15 vda1 v16 vsa9 c17 addata_7 m6 gpio_12 f8 mema_12 n10 memd_30 g18 vda2 w3 vsa10 d1 addata_8 n1 gpio_13 a7 mema_13 w11 memd_31 j11 vda3 b17 vsa11 d19 addata_9 p5 gpio_14 e6 mema_14 u12 memoen_0 p13 vda4 a3 vsa12 t1 addata_10 n2 gpio_15 b7 mema_15 t11 memoen_1 v14 vda5 a17 vsa13 t19 addata_11 p3 gpio_16 c6 mema_16 p11 memoen_2 u16 vda6 b3 vsa14 u3 addata_12 n4 gpio_17 d7 mema_17 l10 memoen_3 w15 vda7 b4 vsa15 u17 addata_13 l9 gpio_18 j9 mema_18 r12 memwrn_0 v13 vda8 c1 vsa16 v2 addata_14 t2 gpio_19 a6 mema_19 w12 memwrn_1 u14 vda9 c2 vsa17 w16 addata_15 p4 gpio_20 f7 mema_20 r13 memwrn_2 t13 vda10 c18 vsb0 d12 adrc n6 gpio_21 d6 mema_21 t12 memwrn_3 l11 vda11 c19 vsb1 h10 adrdy l4 gpio_22 c5 mema_22 u13 pvddpll a14 vda12 u1 vsb2 h9 adtrig l6 gpio_23 b6 membexcn d14 pvsspll f14 vda13 u2 vsb3 b5 adwr r3 iobrdyn d16 memcb_0 f19 romcsn_0 n11 vda14 u18 vsb4 d2 canen_0 e2 iocsn c16 memcb_1 d18 romcsn_1 p12 vda15 u19 vsb5 h7 canen_1 d4 iooen b14 memcb_2 f16 spwclk10mbit_0 a10 vda16 v3 vsb6 j6 canrx_0 d5 ioread d15 memcb_3 e17 spwclk10mbit_1 e11 vda17 w17 vsb7 k8 canrx_1 g8 iowrn a15 memcb_4 e19 spwclk10mbit_2 d10 vdb0 g12 vsb8 n5
4 at7913e advanced information 7833b?aero?05/09 cantx_0 c4 leondsuact r7 memcb_5 e16 spwclkmult_0 d13 vdb1 f10 vsb9 t3 cantx_1 a5 leondsubre v8 memcb_6 h13 spwclkmult_1 h12 vdb2 a8 vsb10 p8 fifod_0 g4 leondsuen n8 memcb_7 g13 spwclkmuxsel h11 vdb3 g7 vsb11 u8 fifod_1 g2 leondsurx u7 memcsn_0 t15 spwclkpllcnfg_0 c14 vdb4 f1 vsb12 r10 fifod_2 f3 leondsutx t8 memcsn_1 n12 spwclkpllcnfg_1 a13 vdb5 j8 vsb13 u11 fifod_3 g1 leonerrorn m7 memcsn_2 t16 spwclkpllcnfg_2 e14 vdb6 h6 vsb14 v12 fifod_4 f5 leonpio_0 p7 memcsn_3 n14 spwclksrc b13 vdb7 k6 vsb15 r14 fifod_5 h4 leonpio_1 t4 memd_0 t17 spwdin_n_0 c11 vdb8 m2 vsb16 u15 fifod_6 g3 leonpio_2 w5 memd_1 r19 spwdin_n_1 l17 vdb9 v5 vsb17 r18 fifod_7 h2 leonpio_3 t5 memd_2 r16 spwdin_p_0 b11 vdb10 w8 vsb18 p14 fifod_8 g5 leonpio_4 v6 memd_3 p16 spwdin_p_1 l18 vdb11 w9 vsb19 n18 fifod_9 h1 leonpio_5 u4 memd_4 p19 spwdout_n_0 e13 vdb12 u10 vsb20 m16 fifod_10 h5 leonpio_6 t6 memd_5 t18 spwdout_n_1 n15 vdb13 v11 vsb21 k12 fifod_11 j7 leonpio_7 w6 memd_6 n16 spwdout_p_0 b12 vdb14 m11 vsb22 k18 fifod_12 j2 leonpio_8 p6 memd_7 p17 spwdout_p_1 m18 vdb15 w13 vsb23 j14 fifod_13 j3 leonpio_9 t7 memd_8 n19 spwsin_n_0 c12 vdb16 t14 vsb24 h16 fifod_14 j1 leonpio_10 m8 memd_9 p15 spwsin_n_1 m17 vdb17 n13 vsb25 g16 fifod_15 k1 leonpio_11 v7 memd_10 l12 spwsin_p_0 a11 vdb18 p18 vsb26 g14 fifoempn d3 leonpio_12 u6 memd_11 k19 spwsin_p_1 l19 vdb19 m12 vsb30 f13 fifofulln g6 leonpio_13 w7 memd_12 l15 spwsout_n_0 f12 vdb20 m13 fifohalfn e1 leonpio_14 r6 memd_13 k16 spwsout_n_1 m14 vdb21 k14
5 at7913e advanced information 7833b?aero?05/09 3. pin description table 2. pin description signal name type function vdb power 3.3v power for the device vda, pvddpll power 1.8v power for the device vsa, vsb, pvsspll power ground for the device sysclk i system clock sysresetn i system reset leonerrorn io, open- drain, output leon error - this active low output is asserted when the processor has entered error state and is halted. this happens when traps are disabled and an synchronous (un-maskable) trap occurs. leonwdn io, open- drain, output leon watchdog - this active low output is asserted when the watchdog times-out. leondsuen i dsu enable - the active high input enables the dsu unit. if de-asserted, the dsu trace buffer will continue to operate but the processor will not enter debug mode. leondsutx o dsu uart transmit - this acti ve high output provides the data from the dsu communication link transmitter leondsurx i dsu uart receive - this active high input provides the data to the dsu communication link receiver. leondsubre i dsu break - a low-to-high transiti on on this active high input will generate break condition and put the processor in debug mode leondsuact o dsu active - this active high output is asserted when the processor is in debug mode and controlled by the dsu. leonpio[15:0] io leon parallel input / output - these bi-directional signals can be used as inputs or outputs to control external devices. gpio[23:0] io general purpose input / output timeclk i external timer clock timetrig[2:1] o external timer trigger - asserted for 8 system clock periods cantx[1:0] o can transmit canrx[1:0] i can receive canen[1:0] o can transmit enable addata[15:0] io adc/dac data adaddr[7:0] io adc/dac address
6 at7913e advanced information 7833b?aero?05/09 adwr o dac write strobe adcs o adc chip select adrc o adc read/convert adrdy i adc ready adtrig i adc trigger mema[22:0] o memory interface address - these active high outputs carry the address during accesses on the memory bus. when no access is performed, the address of the last access is driven (also internal cycles). memd[31:0] io memory interface data - memd[31:0] carries the data during transfers on the memory bus. the processor only drives the bus during write cycles. during accesses to 8-bit areas, only memd[31:24] are used. memcb[7:0] io memory interface checkbitsmemcb[6:0] carries the edac checkbits, memcb[7] takes the value of tb[7] in the error control register. the processor only drive memcb[7:0] during write cycles to areas programmed to be edac protected memcsn[3:0] o sram chip select - these active low signals provide an individual output enable for each sram bank. memoen[3:0] o sram output enable -these active low outputs provide the chip-select signals for each sram bank. memwrn[3:0] o sram byte write strobe - these active low outputs provide individual write strobes for each byte lane. memwrn[0] controls memd[31:24], memwrn[1] controls memd[23:16], etc. romcsn[1:0] o prom chip select - these active low outputs provide the chip- select signal for the prom area. romcsn[0] is asserted when the lower half of the prom area is accessed (0 - 0x10000000), while romcsn[1] is asserted for the upper half. iocsn o i/o area chip select - this active low output is the chip-select signal for the memory mapped i/o area. iooen o i/o area output enable - this active low output is asserted during read cycles on the memory bus. ioread o i/o area read - this active high output is asserted during read cycles on the memory bus. iowrn o i/o area write - this active low output provides a write strobe during write cycles on the memory bus. iobrdyn i i/o area ready - this active low input indicates that the access to a memory mapped i/o area can be terminated on the next rising clock edge.
7 at7913e advanced information 7833b?aero?05/09 membexcn i memory exception - this active low input is sampled simultaneously with the data during accesses on the memory bus. if asserted, a memory error will be generated. fifod[15:0] io fifo data fifop[1:0] io fifo parity fifordn o fifo read strobe fifowrn o fifo write strobe fifofulln i fifo full fifoempn i fifo empty fifohalfn i fifo half-full, half-empty spwclksrc i spacewire transmitter clock source spwclkmult[1:0] i spacewir e clock configuration spwclk10mbit[2:0] i spacewi re clock configuration spwclkpllcnfg[2:0] i spacewi re clock configuration spwclkmuxsel i spacewire clock configuration - configuration external clock when 1, internal pll when 0. spwdin_p[1:0] i, lvds positive spacewire data input, positive spwdin_n[1:0] i, lvds negative spacewire data input, negative spwsin_p[1:0] i, lvds positive spacewire strobe input, positive spwsin_n[1:0] i, lvds negative spacewire strobe input, negative spwdout_p[1:0] o, lvds positive spacewire data output, positive spwdout_n[1:0] o, lvds negative spacewire data output, negative spwsout_p[1:0] o, lvds positive spacewire strobe output, positive spwsout_n[1:0] o, lvds negative spacewire strobe output, negative lvdsref[0:1] power lvds reference voltage for spacewire channels
8 at7913e advanced information 7833b?aero?05/09 taptck i tap clock - used to clock serial data into boundary scan latches and control sequence of the test state machine. tck can be asynchronous with clk. taptdi i tap data input - serial input data to the boundary scan latches. synchronous with tck taptdo o tap data output - serial output data from the boundary scan latches. synchronous with tck taptms i tap mode select - resets the test state machine. can be asynchronous with tck. shall be grounded for end application. ta p tr s t i tap reset - resets the test state machine. can be asynchronous with tck. shall be grounded for end application .
9 at7913e advanced information 7833b?aero?05/09 4. functions and interfaces the at7913e spacewire remote terminal controller (rtc) is a bridge between the spacewire network and the can bus. the at7913e is based on a leon2-ft sparc v8 processor core together with a wide range of interfaces including : ? debug support unit ? leon2-ft peripherals ? interrupt controller ? 32-bit timer ? uart serial links ? 16-bit general purpose input output ? memory interface ? on-chip memory ? fifo interface ? adc/dac interface. ? 32-bit timers ? 24-bit general purpose input output ? can interface ? spacewire link interface ? jtag interface 4.1 leon2-ft processor the spacewire-rtc asic includes the leon 2-ft integer unit (iu) and the meiko floating point unit (fpu). the leon2-ft iu implements the sparc integer instruction set as defined in the sparc architecture manual version 8. the leon2-ft iu has the following features: ? 5-stage instruction pipeline ? separate instruction and data cache interface ? support for 8 register windows ? multiplier 16x16 ? radix-2 divider (non-restoring) to allow for software co mpatibility with existing devices such as the at697e from atmel, the at7913e spacewire-rtc includes all standard leon2-ft peripherals and the debug support unit. the programming model of the spacewire-rt c device is thus compatible with the existing devices, only requiring support for the additional functions and interfaces to be added to the existing software development tools and operating systems. the spacewire-rtc includes a leon2-ft core with 4kbyte instruction and data caches. it also includes a meiko fpu (the same one as included in the atmel at697device).
10 at7913e advanced information 7833b?aero?05/09 4.2 debug support unit the at7913e spacewire rtc includes a hardware debug support to aid software debugging on target hardware. the support is provided through two modules: ? a debug support unit (dsu) ? a debug communication link 4.2.1 debug support unit the dsu can put the processor in debug mode , allowing read/write access to all pro- cessor registers and cache memories. the dsu also contains a trace buffer which stores executed instructions and/or data transfers on the amba ahb bus. the debug support unit is used to control the trace buffer and the processor debug mode. the dsu is attached to the ahb bus as slave, occupying a 2 mbyte address space. through this address space, any ahb master can access the processor regis- ters and the contents of the trace buffer. the dsu control registers c an be accessed at any time, wh ile the processor registers and caches can only be accessed when the processor has entered debug mode. the trace buffer can be accessed only when trac ing is disabled/completed. in debug mode, the processor pipeline is held and the pr ocessor state can be accessed by the dsu. 4.2.2 debug communication link the spacewire-rtc device includes a debug support unit communication link that con- sists of a uart connected to the ahb bus as a master. the debug communications link implements a simple read/write protocol and uses standard asynchronous uart com- munications. the simple communication prot ocol is supported to transmit access parameters and data. a link command consists of a control byte, followed by a 32-bit address, followed by optional write data. 4.3 leon2-ft peripherals the at7913e spacewire-rtc includes a ll the standard leon2-ft peripherals. 4.3.1 interrupt controller the interrupt controller is used to priorities and propagate interrupt requests from inter- nal or external devices to the integer unit. 15 interrupts are handled, divided on two priority levels. a secondary interrupt controller is included to support the 32 additional interrupts used by the additional on-chip peripherals of the at7913e device. 4.3.2 32-bit timer the timer unit implements two 32-bit timers, one 32-bit watchdog and one 10-bit shared prescaler. the functionality of the timers has not been modified with respect to existing implementations, to allow for software compatibility. the watchdog functionality is used for overall software timeout handling and is the basis for error management.
11 at7913e advanced information 7833b?aero?05/09 4.3.3 uart serial links two identical uarts are provided for serial communications. the uarts support data frames with 8 data bits, one optional parity bit and one stop bit. to generate the bit-rate, each uart has a programmable 12-bits clock divider. hardware flow-control is sup- ported through handshake signals. 4.3.4 16-bit general purpose input output the 16-bit general purpose input output port can be individually programmed as output or input. two registers are associated wi th the operation of the port; the combined input/output regist er, and direction register. when re ad, the input/outp ut register will return the current value of th e port; when written, the value will be driven on the port sig- nals. the direction register defines the direction for each individual port. 4.3.5 memory interface the spacewire-rtc memory interface is implemented using the leon2-ft memory controller that supports the following: ? 8-bit prom with sequential edac, ? 8-bit sram with sequential edac ? 32-bit prom/sram with parallel-edac ? 8, 16, 32 bit i/o without-edac (wait-state and/or ready handshake) ? 16 bit gpio (byte-wise) when less than 32 bit memory used 4.4 on-chip memory the spacewire-rtc device includes a fault tolerant on-chip sram with embedded error detection and correction (eda c) and amba ahb slave interface. one error is corrected and two errors are detected, which is done by using a (32, 7) bch code. some of the features available ar e single error counter, diagnostic reads and writes and auto-scrubbing (automatic corr ection of single errors during reads). the on-chip memory comprises a 32-bit wide memory bank of 64 kbytes of data. 4.5 fifo interface this fifo memory can be accessed as an on- chip memory or as an external interface of the chip via the memory interface. the fifo interface supports transmission and reception of blocks of data by use of cir- cular buffers located in memory external to the core. separate transmit and receive buffers are assumed. reception and transmission of data can be ongoing simultaneously. 4.6 adc/dac interface the spacewire-rtc includes a combined analogue-to-digital converter (adc) and digi- tal-to-analogue converter (dac) interface. the adc/dac interface provi des a combined signal interface to parallel adc and dac devices. the two interfaces are merged both at the pin/pad level as well as at the inter- face towards the amba bus. the interface supports simultaneously one adc device
12 at7913e advanced information 7833b?aero?05/09 and one dac device in parallel. address and data signals unused by the adc and the dac can be use for general purpose input out put, providing 0, 8, 16 or 24 channels. the adc interface supports 8 and 16 bit data wi dths. it provides chip select, read/con- vert and ready signals. the timing is programmable. it also provides an 8-bit address output. the adc conversion can be initiated either via the amba interface or by internal or external triggers. an in terrupt is generated when a conversion is completed. the dac interface supports 8 and 16 bit data widths. it provides a write strobe signal. the timing is programmable. it also provides an 8-bit address output. 4.7 32-bit timers the spacewire-rtc includes a general purpos e timer unit that implements one pres- caler and two 32-bit decrementing timers. 4.8 24-bit general purpose input output the spacewire-rtc includes a 24-bit general purpose input output core. the amba apb bus is used for contro l and status handling. the core provides 24 channels. each chann el is individually programmed as input or output. additionally, 8 of the channels ar e also programmable as pulse command out- puts. the default reset configuration for each channel is as input. the default reset value each channel is logical zero. the pulse command outputs have a common 20- bit counter for est ablishing the pulse command length. the pulse command length defi nes the logical one (active) part of the pulse. it is possible to select which of the channels shall generate a pulse command. the pulse command outputs are generated si multaneously in phase with each other, and with the same length (or duration). it is not possible to generate pulse commands out of phase with each other. 4.9 can interface the spacewire-rtc includes a can controller. the can pr otocol is based on the esa hurricane can controller vhdl core. the controller uses the amba apb bus for configuration, control and status handling. the amba ahb bus is used for retrieving an d storing can messages in memory exter- nal to the can controller. this memory can be located on-chip or external to the chip. the can controller supports transmission and reception of sets of messages by use of circular buffers located in memory exter nal to the core. separate transmit and receive buffers are assumed. reception and transmi ssion of sets of messages can be ongoing simultaneously. 4.10 spacewire link interface the spacewire (spw2) module is used for transmitting and receiving data over a spacewire link. it provides support for transmitting any type of protocol or data structure using spacewire packets.
13 at7913e advanced information 7833b?aero?05/09 it provides hardware support for receiving two types of spacewire transfer protocols, and can relay packets of other protocols to software. the spacewire virtual channel transfer protocol (vctp) implements multiple virtual channels (only one implemented in spacewire-rtc) on a single spacewire link. the remote memory access protocol (rmap) implements remote memory access to resources in the node via the spacewire link. data received over the link by the spac ewire codec are temporarily stored in an rxfifo. data are then stored to memory by the spacewire module via direct memory- access. multiple virtual re ceive channels (rxvc) can be used, each with its private memory area to which data are written. in spacewire-rtc one channel (rxvc(1)) is used for storing vctp packets, and one c hannel (rxvc(0)) is used for storing rmap responses, rmap commands not supported by hardware and packets of other types of transfer protocols. all rxvc share the same link. the spacewire module implements hardware support for the rmap. rmap is used for remotely acce ssing resources on the local amba bus. the rmap implementation can receive commands and gene rate responses, utilizing the aforementioned rxfifo and the txfifo. data to be sent are read by the spacewir e module from memory via direct memory access. data are then temporarily stored in a txfifo when forwarded to the spacewire codec for transmission over the link. mult iple virtual transmit channels (txvc) can be used, each with its private send list stor ed in memory from which data are read. in spacewire-rtc one channel (txvc(0)) is used for automatic rmap responses, and another channel (txvc(1)) is used for transm issions set up by the user. all txvc share the same link. rmap responses have priority over transmissions set up by the user. the arbitration is performed for each packet sent. 4.11 jtag interface the jtag interface (com pliant with ieee-std- 1149.1) is used for the purpose of bound- ary scan testing during manufacture and test of printed circuit boards hosting the asic.
14 at7913e advanced information 7833b?aero?05/09 5. typical applications the capabilities of the spacewire-rtc device are not limited to sup port the can bus in the instrument controller unit (icu), but also allows it to be used in an on-board com - puter (obc). the at7913e spacewire rtc is perfectly suit ed for application requiring cost optimiza - tions as it can be used in both payload and avionics. 5.1 at7913e in icu the spacewire-rtc device can be integrated in the instrument cont roller unit (icu) that acts as the payload data processor and mainly receives payload data from instru- ments and produces processed data to be down linked. the main data communication is performed via the spacewire network. th e icu is however controlled and monitored via the can network from the on-board computer (obc). 5.2 at7913e in obc the can controller in the spacewire-rtc dev ice acts as a remote terminal that is being managed by the obc. alternatively, the spacewire-rtc device can be integrated in the on-board computer (obc). since t he obc acts as the network manager on the can network, the can controller carters capability such as node management and time distribution. the obc also communicates or manages the spacewire network via spacewire links. 5.3 at7913e on payload the main application of the spacewire-rtc de vice is however in instruments or individ- ual experiments of the payload. it provides an abundance of interfaces, each with a high degree of programmability and configurability . it is able to acquire analogue and digital data, generated by connected peripherals and to generate discrete commands towards the same peripherals.
15 at7913e advanced information 7833b?aero?05/09 6. electrical characteristics 6.1 absolute maximum ratings table 6-1. absolute maximum ratings stresses above those listed may cause permanent damage to the device. 6.2 dc electrical characteristics table 6-2. 3.3v operating range dc characteristics. 6.3 ac electrical characteristics the following table gives the worst case timings measured by atmel on the 3.0v to 3.6v operating range table 6-3. 3.3v operating range timings parameter symbol value unit supply voltage - 1.8v core voltage vda -0.3 to +2.0 v supply voltage - 3.3v i/o voltage vdb -0.3 to +4.0 v i/o input voltage -0.3 to 4.0 v operating temperature range -55 to +125 c storage temperature range tstg -65 to +150 c esd for pll >1000 v esd for i/o >2000 v parameter symbol min. max. unit conditions operating voltage vca 1.65 1.95 v vcb 3.0 3.6 v input high voltage vih 2.0 v input low voltage vil 0.8 v output high voltage voh 2.4 v iol = 3, 6, 12ma / vcc = vcc(min) output low voltage vol 0.4 v ioh = 3, 6, 12ma / vcc = vcc(min) output short circuit current ios 50 100 ma ma vout = vcc vout = gnd parameter symbol min. max. unit propagation delay, sysclk rising to memcsn_0 falling tp0 18 ns propagation delay, sysclk rising to cantx_0 rising tp1 29 ns propagation delay, sysclk rising to gpio_22 rising tp2 25 ns
16 at7913e advanced information 7833b?aero?05/09 for guaranteed timings on the two operating voltage ranges, re fer to the section xxx of the ? spacewire-rtc (spwrtc) datasheet ? propagation delay, sysclk rising to fifod_1 rising tp3 16 ns propagation delay, spwclksrc rising to spwdout_p_0 falling tp4 14 ns propagation delay, spwclksrc rising to spwdout_n_0 rising tp5 14 ns
17 at7913e advanced information 7833b?aero?05/09 7. package drawings 7.1 mcga349 here is a presentation of the mechanical ou tline of the 349 pins ceramic quad flat pack (mcga 349) package used for the at7913e figure 7-1. mcga349 package
18 at7913e advanced information 7833b?aero?05/09 8. ordering information (*) according to atmel quality flow document 4288, see atmel web site. part-number temperature range package quality flow AT7913EKB-E 25c mcga349 engineering sample at7913ekb-mq -55c to +125c mcga349 mil level b (*) at7913ekb-sv -55c to +125c mcga349 space level b (*)

▲Up To Search▲

Price & Availability of AT7913EKB-E

	To Download AT7913EKB-E Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .